Daiichiseiko Kousoku 2.0 Recycler Fishing Reel Line Spooler Adjustable Clamp

$119.95
RRP $129.95
SAVE $10.00 (8%)

More info.

Make 4 interest-free payments of $29.99 fortnightly and receive your order now.

Sold Out


Registered Shipping - $0.00
Flat Rate Road delivery Australia wide-Free On Orders Over $100
Free Pickup - $0.00
From Jacobs Well - By Appointment - Phone - 07 5546 1489

Anyone that’s spooled a reel at home will know that its not the easiest of processes. There are a few issues that arise, which I’m sure we have all come across.

If your re-spooling a reel with line already on it. The first issue is how do you get the line off? I know I’ve tried making contraptions that fit inside a drill or winding it onto a spool by hand and while these worked to some degree, they were always a bit “clunky” or time consuming. The easy way to strip a reel is of course to just dump the line on the floor and pick up and dispose of when your finished, however this becomes a problem if you intend to keep the line, or reverse wind it back onto the spool.

When it comes to putting new line onto the reel we also run into a few issues. While the assistance of a friend can certainly help the task, attempting the process alone can make for some frustrating times. Two main issues arise, the first is finding something that will hold your spool and allow it to run freely, while the second is trying to keep enough tension on the spool to enable a tight line lay on the reel, especially important for braided lines.

The Kousoku Recycler takes aim at both these problems by not only providing a sturdy base and tension shaft from which to spool off, but also incorporating a geared handle which can be used to crank off line onto a spare spool.

Included in the box is the fully assembled recycler, a short shaft, a long shaft and a screw driver.

 Incorporating a high-speed 3.5x handle and three ball bearings for smooth and speedy handling.

DESIGN & CONSTRUCTION

Taking design queues from what seems like a turbine jet engine, the designers at DaiichiSeiko have not only created a functioning tool but also made it look cool in the process. Its also evident that a lot of attention was also put into the construction of this product. All areas where stress and wear would occur have been constructed out of steel components. The unit also features three ball bearings to keep operation smooth and effortless.

OPERATION

Operation is very simple for both spooling and de-spooling.

To spool a reel:

1. Fix the recycler to a sturdy work surface.
2. Insert the appropriate shaft length and tighten down the screw with the included screw driver.
3. Attach your new line to the shaft, and tension in place with the cog nut.
4. Turn the grey tension knob clockwise until sufficient tension has been applied.
5. Connect your line to your reel and start winding.

NOTE: When spooling try running your line through the guides of your rod, this will give allow you to hold the rod as opposed to the reel stem making the process much more comfortable.

To de-spool a reel:

1. Fix the recycler to a sturdy work surface.
2. Insert the appropriate shaft length and tighten down the screw with the included screw driver.
3. Attach a spare empty spool to the recycler and tension in place with the cog nut.
4. Turn the grey tension knob clockwise until you have just enough tension to prevent the recycler wheel from moving on its own.
5. Connect your line from your reel to the spare spool and start winding with the knob on the side of the recycler.

When de-spooling it can take a little while to get your head around which way to turn the wheel, As the wheel is geared, it will make the spool turn in the opposite direction to that in which you turn it.

(33198)

? Size (excluding shaft): 215 × 95 × 90 mm ? Weight: 460 g (with long shaft used) ? Max. clamp mounting width: 43 mm ? Gear ratio: 3.5:1 ? Shaft size: 8 dia. × 40 mm (short); 8 dia. × 100 mm (long) ? Max. spool installation width: 75 mm (with long shaft used) ? Accessories: Two shafts (short and long), two nuts, two collars, screwdriver, two screws MADE IN JAPAN

SKU 33198
Barcode # 4995915331980
Brand Daiichiseiko

Spooled

By: on 19 April 2019
Have only spooked up one reel with this product and love it. Sure you can get a mate and do the job, but this makes the job that much easier. Set your tension and away you go. No swearing from the mate getting friction burn. Makes a crappy job simple and easy. Works great when taking line off your reel as well. Just a great product. Thanks
(5)

Write a product review


Others Also Bought



More From This Category